Early Javelin Restoration

[Grumpy Northener]

The front torsion bars were next - with the offside one giving up easy to the puller and few well placed blows

IMGP4673.JPG (62.65 KiB) Viewed 8648 times

However the nearside torsion bar was very different story - it took nearly a day to release this - the nuts on the puller kept stripping despite heat being applied to each end of the bar locating socket it would not budge - I built a new tool to hold a long drift in place

IMGP4674.JPG (54.75 KiB) Viewed 8648 times

even with a decent sized sledge hammer the bar was going nowhere

IMGP4675.JPG (64.43 KiB) Viewed 8648 times

I was just about to call it day and had some thoughts on obtaining a hydraulic jaw that I could place between the the terminus of the main chassis rail at the front bulkhead and apply force to the suspension arm but with the remaining front suspension and steering now removed I could turn the suspension arm through to a point that I could just get a couple of dead blows with the sledge hammer on the arm without causing damage - would you guess it but third blow in and out it came.

[Grumpy Northener]

Well a few more bits and we will have a bare shell - still some offside suspension once I rotate the tilter back (still the rear torsion bars to remove but I am not in rush to tackle these)

IMGP4680.JPG (65.32 KiB) Viewed 8647 times

Nearly bare shell status

IMGP4682.JPG (65.84 KiB) Viewed 8647 times

-That will be the easy bit done then - well any idiot can take things to bits - it is the repairs to the shell, mechanical rebuilding & paintwork where the hard work lays so here goes

[Grumpy Northener]

The shell was rotated back to level

IMGP4774.JPG (62.91 KiB) Viewed 8639 times

IMGP4775.JPG (69.47 KiB) Viewed 8639 times

The front of the shell was supported on a timber bearer and axle stands to enable the front tilter to be removed

IMGP4781.JPG (64.32 KiB) Viewed 8639 times

[Grumpy Northener]

The last few mechanical bits could now be removed - the front tilter was preventing the nearside lower suspension arm being withdrawn

IMGP4776.JPG (53.17 KiB) Viewed 8638 times

The torsion bar still requires removal from the arm but I have left it to soak in diesel for a few days

IMGP4779.JPG (56.28 KiB) Viewed 8638 times

Last few mechanicals from the front - steering box & upper suspension set up

IMGP4778.JPG (59.32 KiB) Viewed 8638 times

Stub axle & drum

[Grumpy Northener]

The chassis tilter was also preventing access to a rust effected area on the offside inner wing as the bumper mounting (to which the tilter bracket was bolted to) required removal

IMGP4784.JPG (52.51 KiB) Viewed 8638 times

Difficult to veiw in the image but some very dubious welding had taken place previously - four skins of metal meet at this point and the tin worm always finds a suitable home at this location

IMGP4789.JPG (61.46 KiB) Viewed 8638 times

The box tube for the fresh air supply to the cabin was removed for ease of access

IMGP4790.JPG (62.63 KiB) Viewed 8638 times

In turn revealing several layers of rust trapped by poorly welded over plates

[Grumpy Northener]

The area was templated (retriving pattens that I had retained from a previous Javelin project)

IMGP4794.JPG (57.37 KiB) Viewed 8638 times

Prior to the area being cut out

IMGP4795.JPG (46.4 KiB) Viewed 8638 times

IMGP4796.JPG (63.19 KiB) Viewed 8638 times

[Grumpy Northener]

New sections were fabricated & trial fitted

IMGP4797.JPG (62.98 KiB) Viewed 8638 times

Then welded in to place

IMGP4798.JPG (58.16 KiB) Viewed 8638 times

The additional section is the bumper mounting reinforcing plate

IMGP4800.JPG (50.22 KiB) Viewed 8638 times

Which is spot welded, new holes were drilled for the bumper iron which was trial fitted - the larger hole is for the transfer of fresh air from the cowel to the air tube

[Grumpy Northener]

Other minor areas of the inner wing were made good as required with some small areas of welding

IMGP4780.JPG (60.19 KiB) Viewed 8638 times

Along with this previous accident damage that can be seen on the swaging line of the diagonal panel of the inner wing

IMGP4802.JPG (53.45 KiB) Viewed 8638 times

The air tube required quite a lot of work and was quite thin - not supprising as this gets all the spray and debris from the front road wheel

IMGP4804.JPG (61.81 KiB) Viewed 8638 times

Nothing for it then I opted to fabricate a new one

[Grumpy Northener]

Patterns taken

IMGP4806.JPG (65.6 KiB) Viewed 8637 times

and some time later

IMGP4809.JPG (61.21 KiB) Viewed 8637 times

A trial fitting - I fabricated the tube in 3 sections - the front fluted taper, the main straight section and the rear return - the latter section being sound on the old tube so I cleaned it up and reused it on the new one - once I was happy with the fit I welded the sections up together and cleaned them up

IMGP4810.JPG (53.97 KiB) Viewed 8637 times

- I still have to fabricate a back plate for the tube and spot weld it together - once complete it can all go back together

[junkyarddog]

Very impressive stuff.

Nice welding/fabrication.