Search found 365 matches
- Sun Jan 10, 2016 9:33 pm
- Forum: Technical queries
- Topic: Material for door card re-manufacture
- Replies: 28
- Views: 14405
Re: Material for door card re-manufacture
I will leave the driving of Shadows into swimming pools to Jezza. A few years back a guy drove a Shadow off the ferry slipway into Poole harbour. He survived but the car didn't. Shadows 1 are getting rare. They made 8000 RHD cars. 1/2 exported the RHD countries. Out of 4000 cars sold in the UK it's ...
- Sat Jan 09, 2016 5:39 pm
- Forum: Technical queries
- Topic: Material for door card re-manufacture
- Replies: 28
- Views: 14405
Re: Material for door card re-manufacture
Fortunately my cars don't leak and are garaged when not in use. But regardless of the precautions when used in wet weather damp will get in the car. I use the AC to dry the car. Also my carpets are 100% polypropylene that is like Wilton to look and touch. The Jeep has carpets that are held down by c...
- Thu Jan 07, 2016 9:51 pm
- Forum: Technical queries
- Topic: Material for door card re-manufacture
- Replies: 28
- Views: 14405
Re: Material for door card re-manufacture
Foamex it is then. Next time a door card comes up for remanufacture I shall give it a go. New ideas and all that.
I do question Leather walnut and Wilton in cars due to damp. Especially Wilton carpet.
Bob
I do question Leather walnut and Wilton in cars due to damp. Especially Wilton carpet.
Bob
- Wed Jan 06, 2016 8:42 pm
- Forum: Technical queries
- Topic: Material for door card re-manufacture
- Replies: 28
- Views: 14405
Re: Material for door card re-manufacture
It is in the realms of diy to make door cards that are as good as what MB fitted if not better. Use 3 mm thick marine ply. Cut to shape with holes for clips and furniture. Cover with thin foam use trim adhesive. Cover with cloth, vinyl or leather use trim adhesive. Paint the back with enamel underco...
- Tue Jan 05, 2016 9:16 pm
- Forum: Technical queries
- Topic: Material for door card re-manufacture
- Replies: 28
- Views: 14405
Re: Material for door card re-manufacture
Wickes sells hard board. Also 3 mm marine ply is used by trimmers on the better cars.
Oil tempered hardboard is also available.
Pre cast glass fibre flat sheets.
Check out marine stuff.
Bob
Oil tempered hardboard is also available.
Pre cast glass fibre flat sheets.
Check out marine stuff.
Bob
- Sat Dec 26, 2015 7:57 pm
- Forum: General Chat
- Topic: severe weather
- Replies: 6
- Views: 2426
Re: severe weather
That's a nice thing to offer.
I am in Bournemouth and the temp is 14c and a warm breeze. Quite pleasant. Some are paddling in the sea.
I haven't had the heating on at home. I will be able to use the money saved for tyres.
Bob
I am in Bournemouth and the temp is 14c and a warm breeze. Quite pleasant. Some are paddling in the sea.
I haven't had the heating on at home. I will be able to use the money saved for tyres.
Bob
- Thu Dec 24, 2015 7:18 pm
- Forum: Technical queries
- Topic: Rotor arm?
- Replies: 4
- Views: 2577
Re: Rotor arm?
I believe these rotor arms are red in colour.
Powerspark do electronic ignition for about 40 quid. My cars points and condenser cost out 30 quid. When my points finally wear out I will try out their kit.
Bob
Powerspark do electronic ignition for about 40 quid. My cars points and condenser cost out 30 quid. When my points finally wear out I will try out their kit.
Bob
- Wed Dec 23, 2015 9:21 pm
- Forum: Technical queries
- Topic: Rotor arm?
- Replies: 4
- Views: 2577
Re: Rotor arm?
Power spark and Accuspark have an eBay shop which will have this rotor arm.
Bob
Bob
- Mon Dec 21, 2015 8:22 pm
- Forum: Technical queries
- Topic: Exhaust manifold leak
- Replies: 16
- Views: 5999
Re: Exhaust manifold leak
Many years ago I had a Vellocette LE noddy bike 200cc water cooled horizontally opposed side valve. The right head gasket blew so I faced both heads on my lathe and fitted without gaskets. It ran fine and it can't blow a gasket because it hasn't got any.
45 mph great little bike.
bob
45 mph great little bike.
bob
- Fri Dec 18, 2015 8:11 pm
- Forum: Technical queries
- Topic: Exhaust manifold leak
- Replies: 16
- Views: 5999
Re: Exhaust manifold leak
Gun smiths hold the metal in the flame which condenses the black soot on the surface of the bit. Then they fit the bit and slide it around. Where the soot is rubbed off is the high spots. For stuff like manifolds engineer's blue is easiest and a shoe polish sized tin is about a quid and lasts for ye...